Edinson Borda Villcas. Test de Percepcion Visual Frostig Manual. Uploaded by. MARIA Abs Cambios Uploaded by. Patricio Patri. Manual Autorizacion Btp. Manual Autorizacion Btp. Uploaded by. Patricio Patri · PROBMON1-Ser Omni 6- 25 Min (Problemas). Uploaded by. Patricio Patri · Test Psi Co Tec Nico. Manual Autorizacion Btp Descripción: PROGRAMACIONES BTP INFORMÁTICA HONDURAS M Topographie 2-Approfondissement BTP- TSGT.
|Published (Last):||12 July 2015|
|PDF File Size:||7.60 Mb|
|ePub File Size:||11.98 Mb|
|Price:||Free* [*Free Regsitration Required]|
Now, the nut can be released by turning the pinon with the help of a spanner. Oxycodone 5mg po q4h prn BTPduragesic. Put the lubricating oil Page Electrical wiring should be brought in through water proof conduit connection.
Accidental collisions are not un-common in the field of CNC lathes. Requirements of turret control: Remove the plug, the spring and the valve button. Coolant ring should then be shifted back and clamped in original position.
Drum Cam Sub-assembly Fig Use extraction screws and pull out mankal end plate One revolution of cam shaft completes one indexing inde xing cycle of declamp-index-clamp. Coolant ring as well as coolant flange have provision for angular adjustment.
Remove indexing gear assembly, Inspect the gap, and check the alignment of making to ensure that the nut has been fully tightened. All these signals should stop the operation of the machine, and an indication should be available on the control panel regarding autoriacion nature of the fault.
Dowel pins for ensuring the position are not recommended for the reasons explained earlier. For replacement, loosen the clamp and move the coolant ring to bring the valve in a suitable position to get access to the plug Refer main assembly drawing fig.
If in doubt connect 24V DC supply to the turret. Btp italia i numeri salvo62barbato Education.
Reference mark made on the coolant flanges 26 and 24 can serve as a rough guide. It might be necessary to use a torch light to check the alignment. Manual para estimar edad ysexo en aves del Parque PDF. This can be caused due to accidental collision with lathe chuck or other components. Partial Assembly of Spindle Tool indexing cycle on manual demand: Tighten bolts 15 with a light force.
Figure Bicycle Collisions and Parties at Fault Only a small possibility of requiring replacement.
Remove encoder 61 and mounting flange Angular position of the encoder is important. Coolant passages in tool turret can withstand a maximum pressure of 6 bar. They also give excellent protection against damage by hot chips. Turret should be aligned by dialing surface of the indexing flange. Loosen clamping screws 15 of friction ring coupling and pull out the index gear Following procedure is to be followed for this adjustment.
Then crank the turret through one or two stations to get the alignment. Part Name Part No. Switch is held in a clampand the clamp is bolted to the turret body by socket head screw The tool disc will then sit in an angular position, making it impossible to align the tools.
Remaining components of the cam shaft are to augorizacion assembled at a later stage. Then gently fit the encoder in position ensuring that slot fits properly on the pin. Crank turret by hand, and check the function of switch by watching the signals on the built in LED. Runion BTP 30 avril Documents. Flickering of the light, or inconsistency of LED operation will be an indication of faulty proximity switch.
Instructions for fitment on the machine. For further autorisacion, insert indexing gear assembly fig. Turret is lubricated by medium viscosity gear box oil.
Clamping bolts should use machine washers of extra thickness min. Autodizacion gratis btp – Test24H 2. Bolt holes in the tool disc should be of extra large size to allow for angular adjustment.
It is a difficult task to remove such dowel pins, and to fit new ones. Valve button continuously presses against coolant flange 26 fitted on indexing flange.
In such accidents, the friction joint of Ringfeder slips; and protects the internal mechanism from damage. Simultaneously it is necessary to ensure that the teeth of drive gear 73 and drum cam gear 8 mesh autorizaciin orientation marks properly aligned.
Contactors take much longer time 30 to 40 ms.